一、用途：

链式输送机是一种用于水平或倾斜（≤15°）送粉状、粒状的物料产品，本产品广泛用于建材、建筑、化工、火电、粮食加工、矿山、机械、冶炼、交通、港口和运输等行业。

The chain conveyor is a kind of powdery or granular material for horizontal or inclined (≤15°). This product is widely used in building materials, construction, chemical, thermal power, grain processing, mining, machinery, smelting, transportation, Port and transportation industries.

二、工作原理：

散料各微粒间存在着相互的内摩擦力和内压力，它们在链运机机槽内受到输送链运动带来的与运动同向的拉力作用，使散料间的内摩擦力、内压力增大，当内摩擦力大于物料与机槽壁的摩擦力后，物料在输送链的带动下，向前移动，当料层高与机槽宽的比值满足一定条件时，物流是稳定的，料速约等于链速。

There are internal frictional forces and internal pressures between the particles of the bulk material. They are subjected to the pulling force in the same direction as the movement caused by the movement of the conveyor chain in the slot of the chain conveyor, so that the internal friction and internal pressure between the bulk materials Increase, when the internal friction is greater than the friction between the material and the groove wall, the material moves forward under the conveyance chain. When the ratio of the height of the layer to the width of the groove meets certain conditions, the flow is stable. The material rate is approximately equal to the chain speed.

三、主要特点：

1．输送能力大，输送机允许在较小空间内输送大量物料。

2．输送能耗低，借助物料的内摩擦力，变推动物料为拉动，使其与螺旋输送机相比节电50%。

3．密封和安全，全密封的机壳使粉尘无缝可钻，操作安全、运行**。

4．使用寿命长，用合金钢材经热处理手段加工而成的输送链，其正常寿命大于5年，链的滚子寿命（根据不同物料）≥2-3年。

5．工艺布置灵活，可高架、地面或地坑布置，可水平或爬坡

≤15°安装，可多点进出料。

6．使用费用低，节电且耐用，维修少，费用低，能确保主机的正常运转，以增加产出、降低消耗、提效。

1. The high conveying capacity and efficient conveyor allow a large amount of material to be transported in a small space.

2. The energy consumption of the conveyor is low, and the material is pulled by the internal friction of the material, so that it can save 50% compared with the screw conveyor.

3. Sealed and safe, the fully sealed housing allows dust to be drilled seamlessly for safe operation and reliable operation.

4. The service life of the conveyor chain made of alloy steel by heat treatment has a normal life of more than 5 years, and the roller life of the chain (according to different materials) ≥ 2-3 years.

5. Flexible process layout, can be arranged on the elevated, ground or pit, horizontal or climbing ≤15° installation, multi-point feeding and discharging.

 6. The utility model has the advantages of low use cost, power saving and durability, low maintenance and low cost, and can ensure the normal operation of the host to increase output, reduce consumption and improve efficiency.

四、注意事项：

1．物料温度在60-120℃时，易选用较慢链速。物料超过120℃时，请于本公司技术科联系。

2．若输送长度大于90m或输送一些特殊物料、或用在特殊的场合，用户无法自行选用时，请于本公司技术科联系。

五、维修：

1．检查各部级检的紧固情况，若有松动应及时拧紧。

2．检查各运转部位的润滑情况，应按设备润滑“五定“标准，进行加注润滑油（脂）。

3．检查内外链权与该轮的联接情况，如有磨损或位置变动，应及时处理。

4．检查各链板的连接螺栓的紧固情况，若有松动应及时拧紧。

5．检查减速机的润滑情况，润滑油应符合油标尺刻度要求。

6．工作后对设备进行检查、清理和擦拭，并清理工作场地。 

六、定期保养

  1．链板机在运转半个月时，应对各内外链板、锁片、该轮进行检查，磨损严重时应更换。

2．链板输送机在运转一个月时，应对机头、机尾轴承进行检查，并加注润滑脂及更换密封件。

3．链板输送机在运转一个月时，应对减速机进行检查并补充润滑油及更换密封件。

4. 链板输送机在运转一个月时，应对传动部位的零部件进行检查并更换。

5．一周一小查，3个月一大变，必须保证主从动支架出渡槽的中心线在一条直线上。

6．经常保持减速机干净、整洁。